1、食品加工机械破碎机欧盟CE知识分享指令

MD机械指令：2006/42/EC

2、食品加工机械破碎机欧盟CE知识分享标准：

EN ISO 12100：2010 机械安全 - 用于设计的一般准则-风险评估及风险降低

EN 60204-1：2018 机械安全.机械电气设备.第1部分：一般要求

EN 12331:2003+A2:2010 Food processing machinery - Mincing machines - Safety and hygiene re食品加工机械.破碎机.安全和卫生要求

3、EN 12331:2003+A2:2010适用范围：

1.1 This European Standard specifies re for the design and manufacture of mincing machines (see Figures 1 and 2) used in a stationary position. The machines covered by this standard are used for size reduction of fresh or frozen meat, meat products and fish by cutting in a set of cutting tools. Mincing machines for domestic uses are not included in this standard. Filling mincers are covered by EN 12463 "Food processing machinery - Filling machines and auxiliary machines - Safety and hygiene re”. This standard applies only to machines that are manufactured after the date of issue of this standard. Mincing machines in connection with using a hold to run foot switch are not covered by this standard. These European Standard covers: mincing machines used in shops and preparation rooms; mincing machines used in kitchens where sausages are prepared; mincing machines used industrially; accessories. The extent to which hazards are covered, is indicated in this European Standard. For other hazards which are not covered by this European Standard, machinery should comply with EN ISO 12100 where applicable. This European Standard is not dealing with specific re for the control of mincing machines with foot switch.

1.2 This standard covers the following types: Mincing machine with tray, feed intake and pusher, diameter < 52 mm on feed intake (see Figure 5) Mincing machine with tray, feed intake, restrictor plate and pusher, diameter > 52 mm on feed intake (see Figure 6) Mincing machine with feed intake hopper and cover, screw conveyor, with or without mixing screw in feed intake hopper (see Figure 7) Mincing machine with feed intake hopper, with or without cover, screw conveyor, with or without mixing screw in feed intake hopper, with loading device (continuously or discontinuously) Mincing machines comprise a machine base, a worm casing with a worm, a feed intake tray or hopper, a screw conveyor (and sometimes an additional mixing screw in the feed intake hopper), a set of cutting tools, a lock nut, a loading device, a drive motor and, depending on machine type, electrical, hydraulic and pneumatic components. They will also have various safeguarding devices as examples in clause 5.

1.1本欧洲标准规定了用于固定位置的切碎机（见图1和图2）的设计和制造要求。本标准涵盖的机器用于通过一套切割工具切割新鲜或冷冻肉、肉制品和鱼的尺寸。本标准不包括家用采矿机。灌装切碎机符合EN 12463标准“食品加工机械.灌装机和辅助机器.安全和卫生要求”。本标准仅适用于本标准发布日期之后制造的机器。本标准不包括与使用脚踏开关相关的切碎机。这些欧洲标准包括：商店和制备室使用的切碎机用于制作香肠的厨房的切割机；工业上使用的切碎机；配件。本欧洲标准规定了危险的覆盖范围。对于本欧洲标准未涵盖的其他危险，机械应符合EN ISO 12100（如适用）。本欧洲标准不涉及带脚踏开关的切碎机控制的具体要求。

1.2本标准涵盖以下类型：带有托盘、进料口和推进器的采矿机，进料口直径<52 mm（见图5）带有托盘、进料口、限流板和推进器的矿山机械，进料入口直径>52 mm（图6）带有进料漏斗和盖子的矿山机械、螺旋输送机、，带或不带混合螺旋进料漏斗的采矿机（见图7），带进料漏斗，有或不带盖子，螺旋输送机，带或不含混合螺旋进料斗，带装载装置（连续或不连续），螺旋输送机（有时在进料斗中还有一个额外的混合螺杆）、一套切割工具、锁紧螺母、装载装置、驱动电机，以及根据机器类型的电气、液压和气动部件。他们还将配备各种防护装置，如第5条所示。

4、EN 12331:2003+A2:2010 欧盟CE知识分享测试、检查项目